Pad Mist Eliminator is Used for High Gas-Liquid Separation

Pad Mist Eliminator or mesh mist eliminator pads

Has support grids at the top and bottom. Pad mist eliminator applications require special consideration to assure the removal of entrained moisture in the effluent gas stream.

Woven wire mesh pad mist eliminator

The woven wire mesh pad mist eliminator provides gas-liquid separation at lower mist eliminator cost. However, due to lower gas velocity limitations than vanes it requires larger more costly separator vessels to achieve effective separation.

Mist eliminator pads materials

Mist Eliminator Pads Mesh and grids may be made from most metals and plastics i.e. SS-304, 304L, 316, 316L, 430, Monel, Nickel, Copper, P.T.F.E. (Teflon), H.D.P.E., P.P. etc. and other metals, alloys or plastic which can be drawn or extruded.

Mist eliminator pads are made up from knitted materials with interlocking asymmetrical loops of metal or plastic with typical wire diameters being 0.1 mm - 0.3 mm. By careful choice of wire diameter, Knitted wire products have produced knitted mesh mist eliminators with extremely high free volumes (typically 98-99%) along with very high removal efficiencies and low pressure drop.

Separations & Mass-Transfer Products Division has produced high efficiency knitted wire mesh mist eliminators for free water droplet removal from vapor streams up to 99% removal of droplets 3 micron and larger. Mist eliminator drain roles greatly improve glycol and amine solvent loss reduction. This role feature may be added or specified on any standard mesh pad application for increased droplet removal efficiency performance and overall capacity.

Pad mist eliminator specifications:

1. Pad: demister 2ft. WD × 10ft. LG × 6 inch.
   Thick 316SS.
   Size: 2ft. WD × 10ft. LG × 6 IN THK.
   Material: 316SS.
   Density: 120 KG/m³.
   Contact surface: 400 m²/m³.
   Free space: 98.5%.
   Application: fine entrainment.
   Width: 2 feet.
   Thickness: 6 inch.
   Length: 10 feet.
2. Pad: demister 12 inch width × 120 inch length × 4 inch.
   Thick 316SS .
   Size : 12 IN WD × 120 IN LG × 4 IN THK.
   Type : COALESCER / demister.
   Material: glass fiber -32 SWG .
   Density: 15.3/4 LBS/CFT.
   Contact surface: 400 m²/m³ .
   Free space: 98.5% .
   Application: fine entrainment.
   Width: 2 feet.
   Thickness: 4 inch.
   Length: 10 feet.
3. Stainless steel demister pad ASY, 304SS, KOD 95-301
   Description: Demister pad assembly fuel gas knockout drum.
   Drawing No.: 2207V131.
   Material: 304SS.
   Thickness: 200 mm.
   Density: 144 kg/m.
   Vessel ID No.: 1500 mm.
   Equipment tag No.: QCC-01-AUX-95-301.
   With support rin/ grid, the wire and holding fasteners pad shall be in section.
   KOD operation conditions given below: fluid; fuel gas.

PTFE mist eliminator.

Round wire mesh mist eliminator with empty hole inside.

PTFE mist eliminator.

Round wire mesh mist eliminator.

Wave wire mesh mist eliminator.

Rectangle wire mesh mist eliminator.

Doliform wire mesh mist eliminator.

Wave PP wire mesh mist eliminator.

Stainless steel knitted wire mesh demister pads.

Stainless steel knitted wire mesh demister bars.